The Central Box 100 is a switchboard designed for the complete management of servos in a model with an emphasis on safety. The Central Box has a unique design that provides overload protection at each servo output. The Central Box can manage up to eight servos and fully supports the Jeti EX telemetry system. Up to two receivers with serial (PPM, EX Bus) output can be connected at the same time to the Central Box for complete RF signal redundancy.
With Jeti Duplex 2.4GHz DC/DS transmitters, the full potential of the Central Box can be used, such as an easy way to wirelessly configure the Servo Outputs, EX Telemetry, Fail-Safe Setting or Fast Servo Response. Features:
– Control Management with Configurable Servo Output
– Power Distribution with Overload Protection
– Firmware Updatable via Jeti USB Adapter
– Jeti Duplex EX Bus or PPM Compatible
– Wirelessly Programmable Using DC/DS Tx Device Explorer
– Independent Receiver Signal Inputs (Rx 1, Rx 2)
– Up to 8x Servo Outputs with Overload Protection
– Up to 3x Telemetry Sensors Inputs
– Output Current: 10A Continues/90A Peak
The Jeti telemetry expander module allow you to increase the number of telemetry sensors in your aircraft. The E4 ex Expander allows you to add up to four additional sensors directly to any of the Duplex EX 2.4GHz receivers. Through the Duplex 2.4GHz system and either a JetiBox Profi or Jeti Transmitter you can monitor your data and alarm conditions in real time.
Operational Voltage: 3.2V to 8.4V Dimensions: 36mm x 20mm x 5mm Weight: 4g
Congratulations Gernot Bruckmann on your dual wins last weekend at the Tucson Aerobatics Shootout in Tucson, Arizona. Gernot traveled all the way from Villach, Austria to compete. His first day of practice was a bit rainy but he flew anyways.
His Facebook post reads “How crazy is this, I still can not believe, Tucson Aerobatic Shootout Invitational and Freestyle Champion💪😎 this is really like a dream came true 👌
I really have to thank all who made this possible, of course all my family, sponsors and of course my girlfriend Bettina Schwaiger for all their help and support 👌”
Beautiful, high gloss Carbon Fiber spinners with pre-cut blade slots, special cooling holes, and specially designed aluminum backplate.
Falcon Carbon Fiber spinners come with precut slots for the propeller blades, and specially designed front of the spinner with additional openings for direct intake of the cooling air. The backplate is considered an engineering marvel, anodized, super light with arms shaped to help create additional airflow.
Jeti Telemetry Fuel Flow MFlow2 T and G EX digital flow sensors measure the true fuel flow of gasoline or turbine jet fuel.
The Jeti MFlow2 EX sensor allows you to set your “Low/High Fuel” alarms and gives you accurate reading of fuel consumption. Also allows you to setup remote commands for transmitter wireless value reset. Turbine flow sensor is equipped with Festo 4mm fuel line connectors. Gasoline sensor can be used with Medium 3/32″ (2.4mm), Large 1/8″ (3.2mm) ID fuel tubing.
Through the Duplex 2.4GHz system and either a JetiBox Profi or Jeti Transmitter you can monitor your data and alarm conditions in real time. Make sure that in the Devices folder of your SD card you have a configuration file “MFLOW2.bin”.
Flow Rate: 20 to 800 ml/minute with 2% resolution Operational Voltage: 5V to 8.4V Dimensions: 75mm x 40mm x 30mm Weight: 40g Alarms: Programmable with JetiBox, JetiBox Mini and JetiBox Profi
Servo Driver, Tester and Cycler controls your speed controller or tests any of your servos by providing a variable pulse that simulates the output signal of the receiver. It comes equipped with centering LED light that illuminates when servo is precisely centered.
Servo Driver can also run your electric power systems without needing to use of your RC system. Servo driver can be powered by the BEC in your speed control or by any 4.8-6V battery pack.
– Run your electric motor without your radio
– Test your servos without your radio
– Use to match transmitter throttle to the speed control
– Know what receiver pulse width your motors starts
– Know what receiver pulse width your motor is fully on
Beautiful, high gloss, gel-coated Fiberglass spinners with lite aluminum backplate.
BB Fiberglass spinners do not have precut slots for the propeller blades, so you have the option of using
2, 3 and 4 blade props. Just use a Dremel and make your own slots.