Are you looking for building details or tips for your sailplane? Esprit Tech has everything you’re looking for at the links below:
The Pulsar 3.6E Pro is the latest addition to the ever-growing Pulsar family of hand-made electric s ailplanes. Built at our request, this model is the competition version of the 3.6m Pulsar. The Pulsar 3.6 models use the AG25 modified airfoil designed by Dr. Mark Drela specifically for 3m and larger thermal duration planes. Just like its smaller cousins, the entire model is constructed using free-flight techniques. Get it here!
Our new sailplane launching platform allows you to reach optimal thermal hunting altitudes without the expense of a winch or the hassle of a high-start.
Great for clubs that do not have the space for traditional sailplane launch systems. The platform is made from a 6mm carbon/lite-ply sandwich and mounts to your favorite, 70″ (1780mm) or larger, high-wing model. Find it at our website, here.
Install the mounting brackets that attach directly to your airframe (If needed install fuselage reinforcement plywood/CF plates). The upright portion of the brackets should be 1/8″ (3mm) behind and ahead of the trailing and leading edges of your wing.
Trace the airfoil of the airplane you intend to mount this to onto the side frames of the launch platform. We chose to cover the lower portion of the frame with masking tape so that the marks would show up. Be sure to align the bottom of your airfoil to the bottom of the side frames, as this is critical.
Drill the attachment holes in the side frames by aligning them with the brackets that you installed in step one. Make sure to align the leading and trailing edges of the airfoil that you traced onto the side frames 1/8″ (3mm) inside the brackets. Trim the front edge of the side frames to match the leading edge brackets. You can now cut out the airfoil that you previously traced onto the frames as well as front of the platform.
Measure the width to the outside edges of the front mounting brackets. This is the width of the release platform that needs to be cut for your specific installation. Cut the platform to length. You can at this point also cut two horizontal supports to length, but remember to make them 1/2″ (12mm) longer than the platform to allow for the width of the frames.
Stack the side frames together using both horizontal supports to keep them aligned. Drill three holes in the frames for the three M4 x 230mm support rods. The location of these holes is not critical. Position rods to avoid any contact with fuselage of the launch airplane or sailplane.
Attach the side frames to the four mounting brackets using the included M4x20mm bolts, nuts, and washers. Add the three support rods in their previously drilled holes. Slide the two horizontal supports into the recesses cut in the frames. You can now align the platform onto the horizontal supports and attach the using mechanical fasteners like screws or bolts (Not Supplied). Hook attachment hardware is included with “Tow Hook Release” so do not forget to add it to your shopping cart.
Align the tow hook release on the center of the platform. It is critical that this to be placed in the center and forward of the platform to insure that you get the best attachment and smooth release of your sailplane. Once aligned, you can drill the four holes needed to mount the release. You will now line up and mount your linkage, wire release cable and servo. Make sure when adjusting the tension of the release cable that sailplane is firmly secured to the launching platform as well as pulled forward. Leading edge of the wing has to be aligned against the front platform stops.
Our new sailplane launching platform allows you to reach optimal thermal hunting altitudes without the expense of a winch or the hassle of a high-start. Great for clubs that do not have the space for traditional sailplane launch systems. The platform is made from a 6mm carbon/lite-ply sandwich and mounts to your favorite, 70″ (1780mm) or larger, high-wing model. Get it here http://www.espritmodel.com/sailplane-launching-platform-carbon-black-silver.aspx
Brand New Sailplane Alert: The Elite V 3.1E F5J/ALES Electric Sailplane is waiting for you.
Available in a combination of White, Red, Blue, Orange, or Yellow you can customize this bad boy.
Great sport or entry level competition F5J/LMR (Limited Motor Run) or ALES (Altitude Limited Electric Soaring) electric sailplane. Get it here.
This Pulsar contains a Hacker B20 18L motor, the Jeti Spin Pro 33, MKS DS65K Micro Servos and a BB aluminum Turbo Spinner. Order yours today!
Don’t know what to get your favorite pilot for the upcoming holidays? We’ve got great deals on all Pulsar models right now! Get your shopping out of the way now and relax. Get them here.
Stumped as to what to get your favorite pilot for the upcoming holidays? We’ve got great deals on all Pulsar models right now! Get your shopping out of the way now and relax. Get them here.
Ian Noble sent us these awesome pics of his Minimoa sailplane. According to Noble, “it is such a shame that people overlook it due to its smaller wingspan than is the current trend with scale sailplanes.”